You are Here:

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - James Carter

Pages: [1] 2 3 ... 7
1
Bikers Cafe / Dent pulling day
« on: May 30, 2015, 17:20:18 PM »
Finally got round to filling and painting as best I could!

2
All Technical Issues / Speedo noise
« on: March 24, 2015, 21:41:41 PM »
Has anyone else had this issue. Started today and its the same noise as this guy. Sounds like the noise is lower down than the clocks like the cable itself or the wheel mechanism. Not had time to look at it yet. https://youtu.be/q1EsUboS36M

Sent from my D6503 using Tapatalk


3
Bikers Cafe / Dent pulling day
« on: January 18, 2015, 17:57:47 PM »
Thanks for the info, I'm going to tart mine up as best I can to keep the cost down! Leather seat cover and stainless exhausts were overkill as it is. Got some filler to prep it and may get someone to paint it or do it myself - will see when I get time!


Sent from my iPhone using Tapatalk - Buggy Version

4
Bikers Cafe / Dent pulling day
« on: January 11, 2015, 18:59:01 PM »
Theres a lot of negative feedback on amazon where i got it but its one of those things that you keep having to persevere with! I stripped the gun and fixed the trigger just now as well! It won't do tiny dents but my tank had two tiny and the bigger one in the middle which it did quite well. Took about 20 pulls and two glue sticks. 


Sent from my iPhone using Tapatalk - Buggy Version

5
Bikers Cafe / Dent pulling day
« on: January 11, 2015, 15:43:29 PM »
Final result


Sent from my iPhone using Tapatalk - Buggy Version

6
Bikers Cafe / Dent pulling day
« on: January 11, 2015, 15:36:53 PM »
Having dropped my bike against the corner of my house ages ago I decided to give the Am-Tech dent pulling system a go.

The glue gun trigger broke on the third pull so I regard the gun as super low quality but you can still use it by pushing the sticks through.

After about an hour the result is quite good and with a bit of a sand and a small amount of filler should look ok again!

Recommend a bostic gun though!

1st pic is before and after, others are after a number of pulls!

Sent from my iPhone using Tapatalk - Buggy Version

7
Bikers Cafe / Merry Christmas
« on: January 01, 2015, 13:40:27 PM »
I think it would trap it but i haven't tried. I have heard good things about this stuff and the guy I bought the bike off used it every year. Its just a bit expensive so I haven't bought any yet   http://www.acf-50.co.uk/motorcycle.htm


Sent from my iPhone using Tapatalk - Buggy Version

8
Bikers Cafe / Merry Christmas
« on: December 30, 2014, 20:43:35 PM »
And lots of evil SALT so I've not been out. Mines covered in condensation in the shed!


Sent from my iPhone using Tapatalk - Buggy Version

9
Bikers Cafe / Merry Christmas
« on: December 28, 2014, 21:25:08 PM »
Merry Christmas.......new leather seat cover ooooohhhh nice

10
Bikers Cafe / Vasectomy
« on: December 23, 2014, 13:02:21 PM »
LOL!


Sent from my iPhone using Tapatalk - Buggy Version

11
Bikers Cafe / Vasectomy
« on: December 21, 2014, 13:24:04 PM »
The worst is over!


Sent from my iPhone using Tapatalk - Buggy Version

12
Bikers Cafe / New mirrors and clocks screen
« on: December 21, 2014, 13:23:27 PM »
I've only been out once mind, rear view was better as no cracks in mirrors! But i think the position was about the same.


Sent from my iPhone using Tapatalk - Buggy Version

13
Bikers Cafe / New mirrors and clocks screen
« on: November 29, 2014, 08:12:00 AM »
Got them used off ebay but i reckon these are the same and now you can get ones with indicators in http://www.demon-tweeks.co.uk/motorcycle/mirrors/bike-it-trojan-mirrors


Sent from my iPhone using Tapatalk - Buggy Version

14
Bikers Cafe / New mirrors and clocks screen
« on: November 26, 2014, 08:07:18 AM »
Sorry i am being dense here, if its in the speed/mileometer side, i kept my original and swapped it into the new housing so i don't need to worry then


Sent from my iPhone using Tapatalk - Buggy Version

15
Bikers Cafe / New mirrors and clocks screen
« on: November 23, 2014, 11:42:40 AM »
Yes, they were slotted up to 60mm so fitted ok. I just needed bolts nuts and washers and I put some rubber washers round the mounting holes as well to stop the fairing vibrating and give a wider contact area.

Pages: [1] 2 3 ... 7